Candle making kits
Wax, wicks, fragrance and a pouring jug in one box, which is the simplest way to have a go before buying supplies separately.
Some links on this page are affiliate links. If you buy through them we may earn a small commission, which doesn't change the price you pay.
Wax, wicks, fragrance and a pouring jug in one box, which is the simplest way to have a go before buying supplies separately.
Look for wax sold for container candles, as it holds to the sides of the cup and burns slowly.
Wicks with a metal tab already fixed. Buy a mixed pack of sizes until you know what suits your cups.
Stickers hold the wick to the bottom of the cup; a centring bar keeps it upright while the wax sets.
Use oils made for candles. Essential oils often fade or are not safe at melting temperatures.
A metal pouring pitcher and a probe thermometer make temperatures easy to hit.
Odd cups, trios and single cups without saucers are often inexpensive on eBay.
Making a candle in a teacup is one of the easier candle projects to start with. The cup does the hard work of looking nice, and a wide, shallow cup is a forgiving shape for a beginner. You can do the whole thing in a kitchen in about an hour, plus a day for the wax to set.
Almost any china teacup will work, but check it carefully first. Run a finger round the rim and inside the bowl, and hold it up to the light to look for hairline cracks. A crack that doesn’t matter on a shelf can open up once the wax gets hot. Crazing (the fine web of lines in old glaze) is usually fine, but avoid cups where it’s heavy or the glaze is flaking.
Wider cups are easier to get right than tall, narrow ones, because the melt pool can reach the sides more easily. Cups between about 7cm and 9cm across the top are a good size to start with. Odd cups without saucers are often cheap at charity shops and car boot sales, and you’ll find plenty on eBay too.
The easiest way to work this out is to fill the cup with water to where you want the wax to stop, usually about 1cm below the rim, then pour the water into a jug on a kitchen scale. Soy wax is a bit lighter than water, so multiply the weight of the water by about 0.86. A cup that holds 200g of water will need roughly 170g of wax. Add 10 to 20 grams extra so you don’t run short.
If you’re adding fragrance, the fragrance oil counts as part of the total. Most container soy waxes take between 6% and 10% fragrance, but check the maximum your wax supplier gives, because some waxes sweat or won’t hold the oil above a certain amount.
Wick size depends on the width of the cup, the wax and the fragrance, so there isn’t one right answer. Most wick suppliers publish a chart that suggests a size for a given diameter, and that’s the best place to start. Measure across the inside of the cup at the top of where the wax will be.
If you’re new to it, buy a mixed pack of pre-tabbed cotton wicks and make a test candle before you make a batch. Our guide to wax and wicks explains how to tell whether a wick is too big or too small.
A dip or hole in the middle. This is usually because the wax shrank as it cooled. Keep back a little wax, and once the candle has set, melt it again and pour a thin top-up layer. A hairdryer passed over the surface can also smooth small dips.
Frosting or white patches. Soy wax often develops a white bloom. It’s harmless and doesn’t affect how the candle burns. Pouring a little cooler and letting the candle cool slowly helps.
Wax pulling away from the side. You’ll see this as patches that look wet through the china, if the cup is thin enough to see through. Warming the cup before pouring usually stops it.
The candle tunnels when burned. The wick is too small for the cup, or the candle wasn’t burned long enough the first time. See the safety and care guide for how long to burn it.
Selling candles in the UK comes with labelling rules. Scented candles need hazard labelling under the CLP regulations, and every candle should carry basic safety warnings. If you’re thinking of selling at markets or online, read up on the requirements first. Your fragrance supplier should be able to provide the safety data you need.